Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

Use the tables below to find all the parts needed to connect GreenStar displays physically and electronically.

 

For GreenStar 2 CommandCenter™ 2600/GreenStar 3 2630 Displays:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	PF11019 plus two 19M8648	RE574454	AXE59372
10-mm (0.4-in.) threaded	PF11019 plus two 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).

 

NOTE: Also order power harness (PF90686) and Ethernet cable (PFP12950). Optional protective film for screen (PF90596) is also available.

For 4240 /4640 Universal Display and Extended Monitor:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	AL212683 plus four 19M8648		AXE59372
10-mm (0.4-in.) threaded	UC17356 plus four 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575). 

NOTE: Also order power harness (PFP12435) and Ethernet cable (RE573617). Optional protective film for screen (PF90596) is also available.

This unique bracket connects to the right side of the CommandARM. It is compatible with the cell phone mount (BRE10015), tablet mount (BRE10255), and more. It is also compatible with the touchscreen radio relocation kit (BXX11045) for Premium and Ultimate Comfort and Convenience packages.

The floor insulation kit can reduce cab heat generated by transmission and hydraulic oil temperatures below the cab floor. It can reduce the overall cab temperature, as it works as a thermal barrier. The product comes in a large sheet, which is easily cut to fit the contours of the cab floor.

 

The kit is large enough to fit the floor pan design of 6 through 9 Series Tractor cabs.

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with the extension and adjustment kit (BRE10511)

Keep accessory and monitor wiring neatly contained with these moveable harness hooks. These hooks are specifically designed to easily snap into the factory headliner rail and BRE10574 window mounting bracket and rail with no tools and can be moved as needed. These hooks allow accessory wiring to routed together for a clean look and maximized visibility.

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

There are a variety of additional mounting part solutions available through John Deere to resolve unique mounting configuration needs. The table below includes several additional parts (not shown above) to aid in many different mounting needs.

Use the tables below to find all the parts needed to connect GreenStar displays physically and electronically.

 

For GreenStar 2 CommandCenter™ 2600/GreenStar 3 2630 Displays:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	PF11019 plus two 19M8648	RE574454	AXE59372
10-mm (0.4-in.) threaded	PF11019 plus two 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575).

 

NOTE: Also order power harness (PF90686) and Ethernet cable (PFP12950). Optional protective film for screen (PF90596) is also available.

For 4240 /4640 Universal Display and Extended Monitor:

Mounting style	Display mount (ball)	Tie-rod assembly	Rail mount (ball)
Clamp	AL212683 plus four 19M8648		AXE59372
10-mm (0.4-in.) threaded	UC17356 plus four 19M8648	PF80459	RE576490
Single location bracket	RE558242

The clamp-style mount with GreenStar monitor is not recommended with the vertical rail (BRE10575). 

NOTE: Also order power harness (PFP12435) and Ethernet cable (RE573617). Optional protective film for screen (PF90596) is also available.

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists, and no software is required to complete the install.

A large steel bracket, which spans the entire right-side window, mounts directly to the cab frame for rigidity and strength. The headliner mounting rail (included in this kit) is bolted to the steel bracket. This solution enables the operator to configure and reconfigure monitors and accessories without changing mounting solutions from either location. This rail accommodates clamp-style and T-slot style mount solutions (purchased separately).

 

• Spans the entire right-side window.
• Uses the same factory headliner mounting rail part number (R558980) for easy reconfiguring of accessories.
• Aluminum mounting rail mounts to either the top or underside of the steel bracket, allowing even more options and maximizing visibility preferences.
• Compatible with AXE59372 (clamp-style mount) and BRE10482 and BRE10483 (T-slot ball mounts).

Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

A shorter, 260-mm (10.25-in.) aluminum mounting rail is available. The kit includes all the hardware needed to mount in up to five vertical locations, including upper and lower right-side A-post rollover protective structure (ROPS), upper right-side C-post ROPS, and upper left rear C-post ROPS. It is compatible with both clamp-style and t-slotted ball mounts (purchased separately).

 

• Up to five vertical locations supported with this one rail (kit contains one rail and mounting hardware).
• Uses the same factory headliner mounting rail shape for ease of operator adjustment and preferences.
• Works in combination with other accessory bracket solutions.
• Compatible with AXE59372 (clamp-style mount) and BRE10482 and BRE10483 (T-slot ball mounts).

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right-side window.

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

Mounting a tablet, cell phone, or beverage can be easily done with these solutions. These strong and simple-to-use solutions keep all important items right where they are wanted.

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

The ISO cab implement CAN bus adapter is available to connect any ISO compliant implement or device to an 8R, 8RT, 9R, 9RT, and 9RX (including Scraper Special) Tractor. These connectors are commonly used for planter frame control boxes. 

 

Refer to the operator's manual, sections 16 (CommandCenter™) and 25 (Operator Station), for additional information on ISO implements.

 

NOTE: If the harness is not in use, unplug it from the ISO 11783 location or plug the four-pin connectors together on the harness. If neither of these are done, implement CAN communication errors occur.

The model year 2020 and newer large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or StarFire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

This cable connects the cornerpost Ethernet connector (square) to the GreenStar™ 3 2630 Display Ethernet connector (round). It is required for used with Remote Display Access (RDA), Wireless Data Transfer (WDT), and Machine Sync.

 

The square-to-round connector cable is 80-cm (31.5-in.) long.

This field-installed option reduces stress on the couplers by providing support to the heavy hydraulic hoses used in scraper application. The hydraulic hose support attaches to the back of the tractor next to the drawbar.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

The nine-pin electrical connector is required to allow TouchSet depth control to be used on implements with this feature. The harness provides a position input to the tractor selective control valve (SCV) unit that enables the TouchSet system.
 
This feature allows the operator to adjust height and depth of remote lift cylinders by using the TouchSet controls in the cab.

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

Carpet floor mat

Reduce cab noise and increase comfort with fabric flooring in the cab. This snag-resistant mat is color-matched to the existing tractor cab interior and is easily removed and installed for quick cleaning. The die-cut carpet lays directly over the rubber floor in the cab and is a precise fit. This feature is included in the Ultimate Comfort and Convenience package.

 

Foot throttle kit

The foot throttle kit adds the ability to control engine rpm with the right foot. This allows the operator to control ground speed like an automobile while driving or to make power adjustments to adjust hydraulic flow for operating certain implements.

 

 

Foot decelerator kit

The foot decelerator kit adds the ability to decrease vehicle speed with the right foot. This allows the operator to progressively slow ground speed during precise maneuvering such as at headland turns or around objects without adjusting the set speed. This is exceptionally helpful when operating at full speed for long periods of time.

 

Footrests

The steering column is designed to accept foot pegs, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can still easily add this feature.

 

The kit contains three pegs. Two front-facing pegs thread directly into the steering column. A third peg mounts near the right-side window and is used in combination with the right front peg when the operator seat is swiveled to the right. This upgrade is helpful when operating on steep downhill grades, sidehills, or watching towed implements.

 

Features:

• Direct bolt-on factory finish – no drilling or cutting required
• Heavy gauge steel to support any operator
• Color-matched rubber surfaces for comfort and vibration reduction
• Model year 2022 and newer are compatible with extension and adjustment kit (BRE10511)

 

Sun shade

The cab uses the same sun shade part number in the front, right-side, and rear windows, which are included in the Premium and Ultimate Comfort and Convenience packages. Producers with a Select cab can easily add a sun shade or two.

 

Storage container with lid/ashtray

This storage container is a heavy plastic cup with a hinged lid and foam seal. It keeps ash, snacks, or small items well contained and fits snugly into the smaller cup holder in the upholstery (shown with arrow above) along the right side window.

 

Leather-wrapped steering wheel

Add a little comfort to the day with the leather-wrapped steering wheel. This upgrade is included with the Ultimate Comfort and Convenience package and can be added to the Select or Premium cab by reusing existing mounting hardware.

 

Refrigerator

The refrigerator unit can be added to a cab ordered with a Select Comfort and Convenience package by purchasing the three service parts used in the Premium and Ultimate Comfort and Convenience packages. The main refrigerator unit installs inside the storage compartment behind the instructional seat and requires a weather seal and plug to be added. All wiring already exists and no software is required to complete the install.

 

Rearview mirror (internal)

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

 

Cab power inverter

These kits include an inverter module, wiring harness, and interior color-matched receptacle. The mounting location is at the left C-post interior above the storage compartment or refrigerator unit. This inverter allows an operator to utilize household powered items such as a laptop or power tool charger. The receptacle kits are specific for either type B (compatible with type A and B plugs) or type C style socket (compatible with type C plugs). An interior, color-matched, self-closing cover is included to keep the socket clean from debris when not in use. This same feature is found in Premium and Ultimate Comfort and Convenience packages. Software is not necessary for this update. 

Six-outlet octagonal power strip with pre-installed round convenience outlet (flat pins)

The six-outlet octagonal power strip with pre-installed round convenience outlet is available for field installation for operators that prefer this traditional connection style. This solution can support up to 30 amps of power from the existing, shared 30-amp fused power circuit of the cab. It also provides operators with the same connection in the cab to power equipment they may already have or share with other machines over several generations. The above image shows one mounting option using vertical rail kit BRE10464.

Three-pin octagonal to three-pin round convenience outlet (flat pins) single device adapter

For operators who prefer the six-way power strip connection type but only have one or two accessories to connect in the cab, this single adapter solution is available. The single jumper harness converts one prewired three-pin octagonal style connector into a three-pin round outlet. This solution allows a more economically priced conversion for producers who do not need the full power strip solution.

A similar design for European power connector style is available as RE596960 three-pin octagonal to three-pin round/triangular convenience outlet (round pins) single device adapter.

Harness adapter for citizen band (CB) power connection

Operators using business band/citizen band (CB) radio in their cab will find the model year 2020 7R and 8R Tractors come prewired with antenna coax, power connector, and an NMO antenna base. When wiring the business band radio, the pig-tail connector can be hard wired to the constant power, switched power, and ground wires. It can then be connected directly to the cab base harness power connection point without any cutting or modification, eliminating any need to run new power wires from the fuse panel. These connection points are located under the upper right console next to the open storage tray and mirror/wiper controls, making for a clean install in the cab. The operator only needs to supply the radio unit and NMO style antenna of their choice.

 

Amp-to-flying leads power connector

This adapter allows users to connect aftermarket displays to the universal amp power connector. The female three-socket connector has three flying leads that can be fused to the display harness. Once installed, the display harness will connect to the three-prong amp power adapter in the cab or to the RE67015 outlet adapter.

 

Amp-to-John Deere power outlet adapter

This adapter allows users to connect an amp-style, three-socket connector to the John Deere-style power strip connection type. Use this adapter to quickly and easily connect amp-style power accessories to older, vintage tractors that do not have an amp-style outlet already in the cab without cutting wire harnesses. This adapter can be kept connected into the John Deere-style power strip if users are regularly moving a unique display between vintage and newer tractors in the fleet.

 

External StarFire™ mounting bracket

The model year 2020 large tractors (with updated cab) have a low-profile, offset StarFire receiver integrated into the roof shell. However, there is a mounting bracket solution to add a StarFire 3000 (with deluxe shroud) or Starfire 6000 Receiver. This bracket connects to the center of the front roof near the wiper motor for an exceptional fit with a clean look. The 12-pin wiring harness on both the StarFire 3000 and StarFire 6000 are compatible with the base cab electrical connector.

 

Front license plate mounting bracket

This bracket solution provides a mounting location for countries that require a roadway license mounted to the front of the vehicle. This bracket bolts into place above the front window wiper motor and is also compatible with the external StarFire mounting bracket.

 

Vandal protection door locks with custom key

Add a level of security with this custom door lock handle. This kit replaces the factory-installed handle with a lock cylinder that is different from the ignition start switch and includes two matched keys. Additional keys must be made at a local locksmith.

 

Joystick (multifunction lever)

This optional cross-gate joystick (multifunction lever) replaces fingertip paddle pots for control of selective control valves (SCVs) and allows for programmable hydraulic functionality according to operator preference. It mounts directly to the CommandARM™ console. This is the same joystick (multifunction lever) that is included with a factory-ordered front-end loader.

 

Subwoofer and tweeter kit

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

 

Touchscreen radio relocation kit

Move the touchscreen radio from the factory-installed location (upper right radio bezel) to several other locations with this relocation kit. The kit includes a new headliner bezel, brackets, harness jumper, hardware, and instructions to move the touchscreen unit from its factory location. This kit is for relocation mounting only and does not include the radio unit.

 

Features:

• Allows touchscreen radio to be mounted on rollover protective structure (ROPS) and off the CommandARM bracket or on several other accessory mounting bracket rails sold separately
• Fine-tune the position adjustment with the locking knob on the tie rod

 

Touchscreen video camera upgrade kit

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

 

NOTE: Reference the Cab Mounting Solutions sales guide to view the wide range of mounting accessories for the cab.

The heavy-duty gudgeon is designed for increased loads over the standard gudgeon through larger steering pins and tapered roller bearings. This heavy-duty upgrade increases the durability and strength of the gudgeon and is base equipment on Scraper Special and all 9RX Tractors.

The tow cable is recommended for pulling all 9 Series Tractors in time of needed assistance. Tow cables are available as a factory-installed option on all ag tractors and are base equipment on all Scraper Special Tractors. The tow cable attaches to the rear of the tractor frame, and the quick access connection point is mounted in the front of the tractor.

The tow cable is recommended for pulling all 9 Series Tractors in time of needed assistance. Tow cables are available as a factory-installed option on all ag tractors and are base equipment on all Scraper Special Tractors. The tow cable attaches to the rear of the tractor frame, and the quick access connection point is mounted in the front of the tractor.

The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
 
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.

The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
 
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.

The field-installed electronic SCV kits are made available for tractors needing additional SCVs. These kits provide metered flow rates and timed detents with pressure and load sense compensation. The additional SCV(s) can also be integrated into the Headland Management System.
 
The field-installed kit includes International Organization for Standardization (ISO) lever-assisted breakaway couplers and armrest control lever.

Lift assist wheels are often used with heavy 3-point hitch-mounted implements. The hitch auxiliary raise kit provides hydraulic power for use with the lift assist wheels. Turning and transport are made easier using this feature.

When attaching implement hydraulic hoses to locations on the tractor other than into a selective control valve (SCV), it has always been a challenge to know what kits are required for compatibility. To assist in hooking up planters, seeders, and harvesting equipment where multiple connections are required, auxiliary hydraulic couplers can be added.

 

Hydraulic motor return couplers

 

The hydraulic motor return couplers can be used as a coupler for return oil flow from hydraulic orbital motors and other devices to the tractor's low-pressure return port, labeled ''R'' on the tractor.

Use of this connector specifically in the return to sump port position is for hydraulic components that require a ''leak-off line'' connection to the tractor. Components and implements that require this typically are larger orbital motors that require a drain for seal protection. The connector in the sump port is not to be used to carry return flow from a function to the tractor.

 

Power beyond couplers

 

Power beyond provides live hydraulic power to equipment. This kit supplies oil pressure to implements when the engine is running.
 
Any implement using power beyond must have a way to control oil flow. Use an independent control valve that is pressure-and-flow compensating (supplied separately) to control the oil flow rate from this coupler set.

A rear fender, rear-facing work light is available for the tractor. The kit comes with mounting hardware and a harness which directly connects to the tractor’s existing chassis harness.
 
This mounting location allows for illumination of the hitch and drawbar area to aid in making connections to implements when natural lighting conditions are poor.

Increase light output over halogen work lights with this four-light kit for the front and rear roof corners of the cab. These lights are the same parts included in the Premium and Ultimate Visibility package and are a plug-and-play update. Eliminate bulb replacements while increasing color temperature and lumen output with this eight-light LED upgrade.

The tractor comes equipped with a right side internally mounted rearview mirror. For added visibility and convenience, a second mirror can be added to the left side of the cab. This is exceptionally helpful for watching specific implements or jobs better viewed from the left side.

44.5-mm (1.75-in.), 1000-rpm PTO

• Available on all 9R and 9RT Ag Tractors regardless of transmission.
• Full-power capability for maximum utilization (9R Tractors derate to 238 PTO kW [319 PTO hp] when tractor is stationary)
• 44.5-mm (1.75-in.) diameter shaft

 

Electrohydraulic PTO control

 

The 9R Tractors utilize an electrohydraulic PTO engagement switch to activate the optional 1000-rpm PTO.

Add video capability to the touchscreen radio by adding this cable (video camera purchased separately). When installed, this cable connection port will be located on the outside of the rear cab next to the factory-installed video connection ports used with the Gen 4 display.

Add deep lows and bright high notes to the cab with this sound kit for the Select cab package radios (single DIN radio style). These components are the same factory-installed speakers that come with the touchscreen radio in the Premium and Ultimate cab packages, but are bundled together in this convenient kit for a Delphi radio.

 

The subwoofer is mounted under the operator seat, tweeters are added into the front windshield cab frame (after removing the existing plastic inserts), and an amplifier is positioned under the headliner. The entire kit plugs into the existing cab harness and does not need software to activate.

Add a trailer brake system into the machine to safely and correctly connect the implement’s braking system. This kit allows operators to slow the tractor and the implement together, which is especially helpful for heavy road transport and to manage larger implements while maintaining good stopping power.
 

Always follow correct service intervals and perform required maintenance on the implement braking system by following the implement operator’s manual.

See your true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect fit bracket, harness, and hardware.

See your true ground speed by adding a dual-beam radar. Select the correct mounting bracket for the tractor based on the drivetrain configuration, which includes a perfect fit bracket, harness, and hardware.

Front weights provide additional ballast for the front axle

Cast Quik-Tatch suitcase weights (R127764) can be added to provide additional ballast for implements that exert heavy draft loads and require additional ballast or with hitch-mounted implements that require additional ballast to maintain steering control while transporting.

 

These weights are Quik-Tatch weights that require minimal effort to attach.

Pickup weights

Pickup weights are designed to add fast weight to the tractor. The following pickup weights can be mounted at the front.

 

Support (base weight):

• 900-kg (1948-lb) pickup weight
• 1150-kg (2535.3-lb) pickup weight

All pickup hitches can also be mounted at the rear in the 3-point hitch as a counter weight. To use the third mounting point, an additional center-link bracket is available.

 

1500-kg (3307-lb) and 1800-kg (3968.3-lb) pickup weights

 

The two weights differ only internally, therefore no external differences are visible.

 

The pickup weights can either be installed on the rear hitch or on the front hitch of the tractor using the center-link bracket. They cannot be mounted directly on the front base weight. A front hitch is required. The center-link bracket for installation is included.

The shape of the 1500-kg (3307-lb) and 1800-kg (3968.3-lb) pick-up weights allows for quick and safe mounting. This is ensured by an optimal alignment of the weight and the tractor along with a self-centering design.

 

Major benefits of the design:

• Easy and comfortable
• Less time is required
• Lower risk of injury

 

Due to the user-friendliness, an optimal ballasting of the tractor is guaranteed at any time.

 

The performance of the tractor is used to a greater extent, which leads to higher productivity and a reduction in fuel consumption.

The weights cannot be front installed in combination with Quik-Tatch front weights.

 

NOTE: Ballast should be limited by the lowest of either tire capacity or tractor capacity. The carrying capacity of each tire should not be exceeded. For more ballasting information refer to the Operator's Manual and ballast calculator.

Front weights provide additional ballast for the front axle

Cast Quik-Tatch suitcase weights (R127764) can be added to provide additional ballast for implements that exert heavy draft loads and require additional ballast or with hitch-mounted implements that require additional ballast to maintain steering control while transporting.

 

These weights are Quik-Tatch weights that require minimal effort to attach.

Pickup weights

Pickup weights are designed to add fast weight to the tractor. The following pickup weights can be mounted at the front.

 

Support (base weight):

• 900-kg (1948-lb) pickup weight
• 1150-kg (2535.3-lb) pickup weight

All pickup hitches can also be mounted at the rear in the 3-point hitch as a counter weight. To use the third mounting point, an additional center-link bracket is available.

 

1500-kg (3307-lb) and 1800-kg (3968.3-lb) pickup weights

 

The two weights differ only internally, therefore no external differences are visible.

 

The pickup weights can either be installed on the rear hitch or on the front hitch of the tractor using the center-link bracket. They cannot be mounted directly on the front base weight. A front hitch is required. The center-link bracket for installation is included.

The shape of the 1500-kg (3307-lb) and 1800-kg (3968.3-lb) pick-up weights allows for quick and safe mounting. This is ensured by an optimal alignment of the weight and the tractor along with a self-centering design.

 

Major benefits of the design:

• Easy and comfortable
• Less time is required
• Lower risk of injury

 

Due to the user-friendliness, an optimal ballasting of the tractor is guaranteed at any time.

 

The performance of the tractor is used to a greater extent, which leads to higher productivity and a reduction in fuel consumption.

The weights cannot be front installed in combination with Quik-Tatch front weights.

 

NOTE: Ballast should be limited by the lowest of either tire capacity or tractor capacity. The carrying capacity of each tire should not be exceeded. For more ballasting information refer to the Operator's Manual and ballast calculator.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

36-kg (79-lb) starter weight R311921

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

 

72-kg (159-lb) weight R167153

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

 

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

 

205-kg (452-lb) wheel weight R207782

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

 

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

 

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

 

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

 

70-kg (154-lb) starter weight R569392

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

 

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

 

530-kg (1169-lb) rear wheel weight R563576

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

 

550-kg (1213-lb) wheel weight R563214

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

 

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

620-kg (1367-lb) wheel weight R563212

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

 

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

  

900-kg (1984-lb) wheel weight R341378

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

Mounting kit BRE10026

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

36-kg (79-lb) starter weight R311921

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

 

72-kg (159-lb) weight R167153

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

 

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

 

205-kg (452-lb) wheel weight R207782

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

 

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

 

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

 

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

 

70-kg (154-lb) starter weight R569392

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

 

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

 

530-kg (1169-lb) rear wheel weight R563576

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

 

550-kg (1213-lb) wheel weight R563214

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

 

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

620-kg (1367-lb) wheel weight R563212

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

 

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

  

900-kg (1984-lb) wheel weight R341378

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

Mounting kit BRE10026

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

36-kg (79-lb) starter weight R311921

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

 

72-kg (159-lb) weight R167153

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

 

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

 

205-kg (452-lb) wheel weight R207782

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

 

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

 

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

 

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

 

70-kg (154-lb) starter weight R569392

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

 

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

 

530-kg (1169-lb) rear wheel weight R563576

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

 

550-kg (1213-lb) wheel weight R563214

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

 

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

620-kg (1367-lb) wheel weight R563212

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

 

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

  

900-kg (1984-lb) wheel weight R341378

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

Mounting kit BRE10026

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

36-kg (79-lb) starter weight R311921

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

 

72-kg (159-lb) weight R167153

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

 

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

 

205-kg (452-lb) wheel weight R207782

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

 

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

 

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

 

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

 

70-kg (154-lb) starter weight R569392

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

 

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

 

530-kg (1169-lb) rear wheel weight R563576

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

 

550-kg (1213-lb) wheel weight R563214

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

 

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

620-kg (1367-lb) wheel weight R563212

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

 

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

  

900-kg (1984-lb) wheel weight R341378

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

Mounting kit BRE10026

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

 

36-kg (79-lb) starter weight R311921

When front mounted suitcase weights cannot be used, add additional ballast to the front idler wheels of 8RT Tractors. This helps offset the weight of a hitch-mounted or drawn implement that exerts heavy loads on the rear of the tractor. These starter weights add 36 kg (79 lb) each and the additional weight of R167153 can be added for even more ballast.

 

72-kg (159-lb) weight R167153

These weights fit 965-mm (38-in.) rims or larger as well as 2T idlers.

 

Add these weights to starter weight R311921 on 8RT Tractors or build a rear wheel ballast foundation with these 72-kg (159-lb) weights. These weights are required for mounting the 205-kg (452-lb) R207782 weights for wheeled tractors on the outside of the wheel hub. These can be used on the inside of inner drive with two x 205-kg (452-lb) R207782 weights (not compatible with 1524-mm [60-in.] tread setting).

 

205-kg (452-lb) wheel weight R207782

Add additional rear ballast on wheeled tractors by adding these 205-kg (452-lb) wheel weights.

 

These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side; see Parts catalog for mounting hardware. These weights stack (nest) to themselves and can be bolted directly to the inside hub or to the outside hub using a starter weight (R167153). See the ballast calculator for mounting limitations. There is a maximum stack of three weights on the outside of the hub and maximum stack of two weights on the inside of inner drive wheel.

 

NOTE: Wheel weight kit BL15076 includes two 410-kg (904-lb) R207782 weights and mounting hardware.

 

NOTE: Wheel weight kit BL15071 includes two starter weights (R167153) and weight kit BL15076 for a complete left- and right-side outside hub mounting solution totaling 554-kg (1221-lb).

 

70-kg (154-lb) starter weight R569392

This starter wheel weight fits 1066-mm (42-in.) or larger rims and adds an additional 70-kg (154-lb) of ballast (each).

 

Use these starter weights for mounting R563576, R563214, or R341378 weights to the outside of the outermost hub. They are not compatible with the rack-and-pinion axle. These starter weights can only be mounted to the outside hub of the drive wheel or outside hub of the dual wheel hub.

 

530-kg (1169-lb) rear wheel weight R563576

Add rear ballast on wheeled tractors by adding these 530-kg (1169-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These weights can only be mounted to the outside hub.

 

550-kg (1213-lb) wheel weight R563214

Add rear ballast on wheeled tractors by adding these 550-kg (1213-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392. Unique cast features keep weights securely aligned. These weights are intended to mount between the starter weight and the 900-kg (1984-lb) weights. The 550-kg (1213-lb) weights are not intended to be the outermost facing weight but are for operators that desire rear wheel ballast beyond the 900-kg (1984-lb) weights. Order as a single weight per side.

 

In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

620-kg (1367-lb) wheel weight R563212

620-kg (1367-lb) wheel weight R563212 (inner and outer face shown)

 

Add rear ballast on wheeled row-crop tractors by adding these 620-kg (1367-lb) wheel weights.
 
These weights fit 965-mm (38-in.) rims or larger. Order as a single weight per side. These weights can be bolted directly to the inside hub only.

  

900-kg (1984-lb) wheel weight R341378

Add John Deere’s largest single rear ballast wheel weight option for wheeled tractors with these 900-kg (1984-lb) wheel weights.

 

These weights fit on the outermost hub on 1066-mm (42-in.) or larger rims using starter weight R569392 or kit BRE10026. Unique cast features securely align R563214 in a stack. Order as a single weight per side. In the case of duals or triples, do not mount this weight between two hubs. They are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

 

Mounting kit BRE10026

This kit fits 1066-mm (42-in.) rim or larger and includes the necessary starter weights and hardware to mount the 900-kg (1984-lb) wheel weights with no additional rear wheel ballast. This kit adds an additional 70-kg (154-lb) for a total of 970-kg (2108-lb) when mounted with two R341378 weights. They mount to the outermost hub and are not compatible with the rack-and-pinion axle. These can only be mounted to the outside hub.

Idler weight TR110515

One weight can be installed on each of the eight outside track idlers. It is recommended to install in groups of four, filling one axle first and then the other for a total of up to 560 kg (1232 lb) of total additional ballast.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Wheel spacers are available to push the front wheels to a 3-m (9.8-ft) row spacing width. Two kits are available based on the hub bolt circle diameter.

 

In situations where additional flotation or traction is necessary, such as heavy draft loads or exceptionally tough field conditions, dual wheel extensions are available for both the front and rear axle. These kits provide a correctly spaced mounting surface to bolt on a second set of hubs and tires. A variety of extension options are available; they are specifically designed for John Deere bolt patterns and axle types.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Wheel spacers are available to push the front wheels to a 3-m (9.8-ft) row spacing width. Two kits are available based on the hub bolt circle diameter.

 

In situations where additional flotation or traction is necessary, such as heavy draft loads or exceptionally tough field conditions, dual wheel extensions are available for both the front and rear axle. These kits provide a correctly spaced mounting surface to bolt on a second set of hubs and tires. A variety of extension options are available; they are specifically designed for John Deere bolt patterns and axle types.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Wheel spacers are available to push the front wheels to a 3-m (9.8-ft) row spacing width. Two kits are available based on the hub bolt circle diameter.

 

In situations where additional flotation or traction is necessary, such as heavy draft loads or exceptionally tough field conditions, dual wheel extensions are available for both the front and rear axle. These kits provide a correctly spaced mounting surface to bolt on a second set of hubs and tires. A variety of extension options are available; they are specifically designed for John Deere bolt patterns and axle types.

NOTE: The information below is intended to show a more complete portfolio of options available for this area of the machine. Check the table below to verify specific model and configuration compatibility.

Wheel spacers are available to push the front wheels to a 3-m (9.8-ft) row spacing width. Two kits are available based on the hub bolt circle diameter.

 

In situations where additional flotation or traction is necessary, such as heavy draft loads or exceptionally tough field conditions, dual wheel extensions are available for both the front and rear axle. These kits provide a correctly spaced mounting surface to bolt on a second set of hubs and tires. A variety of extension options are available; they are specifically designed for John Deere bolt patterns and axle types.